castingsraka.blogg.se - Fz 09 ecu flash

#Fz 09 ecu flash install
#Fz 09 ecu flash full
#Fz 09 ecu flash software

Stylish, machined, anodized black bezel and slim enclosure.

The Narrowband to Wideband O2 sensor adapter screws into a 12mm Narrowband bung, allowing you to use a Wideband O2 sensor with a Narrowband bung. The Stainless Steel 12mm Narrowband Bung Bolt allows you to block off a Narrowband O2 bung allowing the Narrowband sensor to be entirely removed from the bike. This Race version of the bung bolt is light weight and has holes pre-drilled for lock wiring. The Stainless Steel Wideband Bung Bolt allows you to block off a Wideband O2 bung when the Wideband O2 sensor is not installed. You can weld this bung into exhaust systems that do not have a Wideband O2 bung.

High Quality 18mm Titanium Wideband O2 Bung.

High Quality 18mm Stainless Steel Wideband O2 Bung. Zeitronix ZT-3 Wideband O2 Installation Guide Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software. This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Diagnostics: Read and Clear Fault Codes - (Requires Applicable V3 Interface).Woolich Racing AutoTune - (Requires Applicable LogBox + Zeitronix Package).Race Shift Pattern Sensor Configuration - (Requires Race Tools).Pit Lane Limiter - (Requires Race Tools).

#Fz 09 ecu flash software

Purchase this item to gain access in the Woolich Racing Tuned software to the stock bin files for the 2016-2020 Yamaha MT-09.įeatures available for Yamaha FZ-09 / MT-09 2016-2020

#Fz 09 ecu flash install

If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).Ģ016-2020 Yamaha FZ-09 / MT-09 Launch Control Keyīin File Definitions - for use in Woolich Racing Tuned softwareĢ016-2020 Yamaha MT-09 Stock Bin File Definitions You can purchase this as a package on the product page for your bike. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. Woolich Racing Race Tools requires you to Write the ECU. *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness. ** This harness uses the stock O2 Sensor plugs on the bike's harness, the stock O2 sensor should be removed from the bike and disabled in the WRT software.

* Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. Pit Speed Limiter RPM can be configured.***Įngine Warm Up parameters are configurable.*** Launch Control allows you to configure Delay, Launch RPM and Hold Speed.

#Fz 09 ecu flash full

Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations.Īutoblipper Opening and Duration maps are fully configurable per gear.

Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.

Yamaha Race Tools Type 2 which allows the quickshifter to be plugged into the bikes wiring harness**.

Shift rod for standard shift configuration*.

High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.

The Race Tools package allows you to enable Autoblipper, Quickshifter, Engine Warm Up, Pit Speed Limiter and Launch Control in the Stock ECU. Race Tools: Quickshifter, Launch Control, Pit Speed Limiter